Repaplast Finish 2-Component Mixture

Description

Repaplast Finish is a 2-component epoxy plaster specially developed for plastics, which is extremely well suited for the fast repair of damage to plastic parts. The product forms an ideal transitional layer to the lacquer system.

Repaplast Finish is ideal for filling and smoothing out scratches and irregularities in plastic parts. If cracks and holes in these parts are first repaired with Repaplast Repair Black or Repaplast Repair Grey, Repaplast Finish can be used afterwards as a fine undercoat for the lacquering. The product can be sprayed over using almost any modern paint system.

Repaplast Finish has a perfect adhesion to many plastics as well as lacquered and bare metal parts. In combination with the high temperature resistance and the high flexibility of the product, this property helps keeping the risk of island formation to a minimum. Due to its fast hardening, the product is ready to be sanded after only 20 minutes.

Repaplast Finish contains no solvents, as a result of which it is not subject to shrinkage or cracking. Neither does the product contain isocyanates.

Repaplast Finish is packed in a handy twin cartridge. Due to the 1:1 mixing ratio, it is very easy to dose and both products are consumed at an even rate. As a result, Repaplast Finish is both very easy to use and very economical.

See also: Repaplast Plastic Repair System

Properties

• 2-component epoxy plaster.
• Ideal transitional layer to the lacquer system.
• Perfectly suitable for filling and smoothing out scratches and irregularities.
• Can be perfectly sprayed or painted over.
• Very flexible with excellent adhesion to most plastics.
• Fast curing, sandable after 20 minutes.
• Perfectly sandable due to its fine and closed structure.
• Handy twin cartridge allowing easy and exact dosing of the product.

Instructions for use

• Surface preparation: The surface must be clean, dry and free of grease. Clean surfaces with Innotec Repaplast Cleaner Antistatic and pre-treat with Innotec Repaplast Primer.
• Application method: Put the accessory into the cartridge and place the cartridge in the Easy Grip Gun. Remove the screw cap, squeeze out the first 2 cm of product and discard it. Then squeeze out the necessary amount of product and mix until a homogeneous colour is obtained. Cover the surface to be repaired with Innotec Repaplast Primer and allow to evaporate for 10 minutes. Apply the mixture on the damaged spot and smooth with a spatula or a rubber spatula. After 20 minutes at 20°C, Repaplast Finish is perfectly sandable. For an OEM finish, always insulate the Repaplast Finish with a 1 or 2 component priming material. After use, close the cartridge by means of the plug and screw cap.

Technical information

• Base: 2 component epoxy
• Density: 1600 kg/m³
• Consistency: Pasty
• Hardness: 50 (Shore D)
• Temperature resistance: 75°C
• UV resistance: Moderate. UV does affect the product if left uncoated and in direct sunlight. Once coated with a top coat or primer the product is UV resistant.
• Water resistance: Excellent
• Solvent resistance: Excellent
• Acid resistance: Good
• Shrinkage: 2% after full cure
• Application conditions: +5°C to +35°C
• Type of surface: Almost every modern type of plastic and plastic mixture (including PUR, PP, TPO, RIM, TPUR), wood, primed glass, lacquered and non-lacquered metal.
• Surface preparation: The surface must be clean, dry and free of grease. Clean surfaces with Innotec Repaplast Cleaner Antistatic and pre-treat with Innotec Repaplast Primer.
• Application method: Put the accessory into the cartridge and place the cartridge in the Easy Grip Gun. Remove the screw cap, squeeze out the first 2 cm of product and discard it. Then squeeze out the necessary amount of product and mix until a homogeneous colour is obtained. Cover the surface to be repaired with Innotec Repaplast Primer and allow to evaporate for 10 minutes. Apply the mixture on the damaged spot and smooth with a spatula or a rubber spatula. After 20 minutes at 20°C, Repaplast Finish is perfectly sandable. For an OEM finish, always insulate the Repaplast Finish with a 1 or 2 component priming material. After use, close the cartridge by means of the plug and screw cap.
• Tack free: 10 minutes
• Curing time: 1,5 hour (at 21°C)
• Sandability: After ± 20 minutes (at 20°C). If you are spraying over Repaplast Finish, sand down with P120, then P220, P320, P400 and P500 sandpaper.
• Paintability: After ± 1,5 hours. Compatible with almost all modern paint systems. Due to the huge variety of paint types on the market, it is best to test the paint beforehand.
• Cleaning of materials used: With Innotec Repaplast Cleaner Antistatic
• Cleaning of hands: With Innotec Power Scrubs or with Innotec Safe Hand Clean Plus and water
• Shelf life: 1 year in original, unopened packaging
• Storage conditions: Store cool and dry
• Type of batchcode: F
• EAN Code: 5400563028292