Multiflex Coating HS Plus Black

Description

Multiflex Coating HS Plus is a highly flexible stone chip protector with perfect anti-corrosion and sound deadening qualities. Because of its ease of use, the original structure can be perfectly imitated.

Multiflex Coating HS Plus is isocyanate-free and retains its flexibility at all times. The product offers perfect adhesion to bare metal and primed metal. It is extremely fast drying and after full curing it can be sprayed over with just about any type of modern paint system.

Multiflex Coating HS Plus can be used for repairs to vehicles and to restore the factory original coating. On vehicles these coatings are applied to the sills, wheel arches, and other bodywork parts.
Another important property of the product is that it is resistant to solvents when fully cured.

The economical 1 litre packaging makes Multiflex Coating HS Plus perfect for spraying with the Pressure Pot Gun or Pressure Gun Basic. The wide range of settings available on these guns allows you to spray layers of any thickness and to copy lots of different structures.

Properties

• Ideal to imitate OEM structures.
• Free of isocyanates.
• Easy to apply.
• Perfect adhesion to bare metal and primed metal.
• Can be painted over after full curing with almost any modern paint system.
• Perfectly sandable when dry.
• Resistant to solvents when fully cured.
• Remains flexible and does not age.
• UV resistant.
• Extremely high solid content, so perfectly suited for applications where a large layer thickness is desired.

Instructions for use

• Surface preparation: The surface must be clean, dry and free of dust and grease. it is advisable to lightly sand the surface. Clean surfaces with Innotec Multisol.
• Application method: Shake can well before use. Spray at 2-4 bar using the Innotec Pressure Pot Gun or Pressure Gun Basic. Always apply the product in a smooth, closed layer. When applying several layers, leave 10 minutes for the product to evaporate in between. Infra-red drying is possible 10 minutes after applying the last layer and with medium wave infrared radiant heat (IR-B).

Technical information

• Base: Mixture of rubbers and synthetic resins and specific fillers
• Density: 1080 kg/m³
• Consistency: Thick fluid
• Solvents: Mixture of aromatic and aliphatic solvents
• Flash point: < 0°C
• Temperature resistance: -40°C to +90°C (short-time limit +210°C)
• UV resistance: Good. Slight change in colour may appear.
• Water resistance: Good
• Solvent resistance: Good, after curing
• Tests: Salt spray test (according to DIN 50021): 600 hours, Ri 0 at 350µ dry layer
• Application conditions: +15°C to +30°C
• Type of surface: Bare and primed metals, aluminium, etc.
  If Multiflex Coating HS Plus is to be applied over a seam sealant, we recommend Innoflex-Sealer H2O or Spray-Seal HS-m as an optimal seam sealant, whereby it should be noted that Spray-Seal HS-m must be pre-treated with Repaplast Primer before over-spraying if it has dried for 4 hours or more.
• Surface preparation: The surface must be clean, dry and free of dust and grease. it is advisable to lightly sand the surface. Clean surfaces with Innotec Multisol.
• Application method: Shake can well before use. Spray at 2-4 bar using the Innotec Pressure Pot Gun or Pressure Gun Basic. Always apply the product in a smooth, closed layer. When applying several layers, leave 10 minutes for the product to evaporate in between. Infra-red drying is possible 10 minutes after applying the last layer and with medium wave infrared radiant heat (IR-B).
• Dust dry: After ± 20 minutes (at 20°C / 65% relative humidity)
• Curing time: ± 2 hours (at 20°C / 65% relative humidity / 500µ wet layer thickness)
  ± 1 hour (at IR drying / 500µ wet layer thickness)
• Recommended layer thickness: 500µ (wet)
• Sandability: Good, after full cure
• Paintability: Can be sprayed over after full curing (depending on layer thickness). Before Multiflex Coating HS Plus can be sprayed over, however, it should be sanded with an abrasive cloth (grey) or a P320 sandpaper. Due to the huge variety of paint types on the market, it is best to test the paint beforehand.
• Cleaning of materials used: With Innotec Multisol
• Cleaning of hands: With Innotec Power Scrubs or with Innotec Safe Hand Clean Plus and water
• Shelf life: 2 years in original, unopened packaging
• Storage conditions: Store cool and dry
• Type of batchcode: F
• EAN Code: 5400563008782